All mrci frames transferred throughout this application have an 8bit numeric value to indicate the type of data being passed with the binary data. The type id enum values are as follows:
This is text that can be displayed directly to the user, passed as command line arguments to be processed or used to carry text data within other data types.
This is a file transfer type id that can be used to transfer any file type (music, photos, documents, etc...). It operates in its own protocol of sorts. The 1st GEN_FILE frame received by the host or client is TEXT parameters similar to what you see in terminal command lines with at least one of the arguments listed below. The next set of GEN_FILE frames received by the host or client is then the binary data that needs to be written to an open file or streamed until the limit defined in -len is meet.
The host or the client can be set as the sender or receiver of the GEN_FILE binary data. This designation is determined by what the command defined in genfile type when the NEW_CMD frame was sent. A genfile type of 2 sets the client as the sender and the host as the receiver. Genfile type 3 sets the client as the receiver and the host as the sender.
see section 3.3 for an example of how GEN_FILE works.
* **-client_file** (string) | this is the file path to the source/destination file in the client's file system.
* **-remote_file** (string) | this is the file path to the source/destination file in the host file system.
* **-single_step** | the presents of this argument tells both the client and host to operate in single step mode. single step mode causes the receiver of the binary data whether host or client to send an empty GEN_FILE frame after successfully receiving the data. this then tells the sender to send the next GEN_FILE frame containing binary data for the file and the cycle continues until len is meet. if this argument is not found, the sender can simply send all GEN_FILE data without waiting for an empty GEN_FILE from the receiver.
* **-truncate** | this indicates to whoever is the receiver to truncate the file being written to.
* **-force** | in some cases, the receiver might need to overwrite the target file. the presents of this argument tells it to overwrite without asking the user. the host should never send this argument and the client should ignore it if it is received from the host.
```ERR```
This type id is similar to TEXT except it indicates that this is an error message that can be displayed directly to the user if needed.
This id can be treated exactly like TEXT except this tells the client that the command is prompting for private information from the user so it sould hide or do not echo the next TEXT data that the command is expecting, like a password or other sensitive data.
```PROMPT_TEXT```
This is similar to PRIV_TEXT expect it is not asking for private information. It is simply prompting for non-sensitive information from the user.
Also formatted exactly like TEXT but this indicates to the client that this is a large body of text that is recommended to be word wrapped when displaying to the user. It can contain line breaks so clients are recommended to honor those line breaks.
All commands started during the session returns this type id when it has finished it's task. It carries a 16bit unsigned integer indicating the result of the task that the command was running.
```
enum RetCode : quint16
{
NO_ERRORS = 1, // task execution completed without any issues.
ABORTED = 2, // the task aborted via user or host intervention.
INVALID_PARAMS = 3, // invalid/missing parameters prevented the task from executing.
CRASH = 4, // the command process has crashed.
FAILED_TO_START = 5, // the command process could not start.
EXECUTION_FAIL = 6, // command specific error prevented execution of the task.
CUSTOM = 7 // indicates a custom return code.
};
notes:
1. the custom return code can be additional data added to the end of the 16bit
integer that can carry additional data about the result of the task. it can
This type id doesn't carry any actual data. It is used to tell the host to stop/terminate the command id and branch id that was used to send it. It does not actually terminate the module's process within the host, it will only tell it to stop what it is currently doing. This will also terminate any commands in a prompt state.
This works similarly to TERM_CMD except it will also terminate the module process. The module process will have 3 seconds to shutdown gracefully before it is force killed by the host session.
This type id doesn't carry any actual data, instead can be used to tell the host to pause/yield the command id and branch id that was used to send it. All modules are not obligated to support this feature but it is highly recommended to do so.
This is a data structure that can be used by modules to run async commands. Each async command have a specific 16bit command id followed by a payload that can contain any data of any format depending on the async command id. A full discribtion of the async commands and the data they carry can found in section [5.1](async.md) and [5.2](async.md).
This is formatted extactly as PEER_INFO except it is used by the ASYNC_LIMITED_CAST [async](async.md) command to tell all peer sessions that receive it to forward the same frame to their own clients and return PEER_INFO frames about themselves to the session that sent the PING_PEERS.
This is a fixed length 28byte(224bit) sha3 hash of a client's session id connected to the host. This is unique to just the client's tcp connection with the host. This changes upon re-connection.
This is formatted extactly like PEER_INFO except it is allowed to be sent directly to a peer session without retriction via the ASYNC_P2P [async](async.md) command. It will be up to the target peer to respond with a P2P_OPEN for the session to then unrestrict ASYNC_P2P so it will then be able to send/received other TypeIDs with this peer until P2P_CLOSE is sent/received. P2P_CLOSE can also be sent to decline the request.
This is a 8bit integer value from 0-100 indicating the percentage progress of the command. All long running module commands are encouraged to use this to update the client on command progress; sending it in a 1-5 second pulse rate.
format: ```1byte - 8bit integer (0-100)```
```PROG_LAST```
This is formatted and treated exactly like PROG except it indicates to the client that this is the last progress update for the current string of progress updates. So at the client side, progress strings/pulses should appear with a single or multiple PROG frame(s) and then end with PROG_LAST. Receiving an IDLE should also end the progress string if seen before PROG_LAST.
* The client has a file called */home/foo/bar.mp3* and wants to upload it to the host file */home/host/music/bar.mp3* and the client knows the file size is 512bytes.
This only needs to be done if the command call needs to be modified by host and if the client supports such a thing. In this example, host will just return an empty GEN_FILE because there is no need for modification.
At this point, the host will then need to check of the destination file: /home/host/music/bar.mp3 already exists. If it does, the host will need to ask the user if it's ok to overwrite.
Once the host confirms it is ok to write to the destination file, it will then need to send another empty GEN_FILE to the client to confirm that it is ready to start receiving GEN_FILE frames from the client through command id *768* that will contain binary data to be written to the destination file until -len (512 bytes) is meet.
