64fe9fcad0
created setup, build and install scripts to make it easier and convenient to compile and install the application from source. no plans distribute pre-compiled binaries because it's just so much easier to guarantee the application will actually work in the target machine when compiled by the target machine.
112 lines
4.6 KiB
Markdown
112 lines
4.6 KiB
Markdown
# Motion Watch #
|
|
|
|
Motion Watch is a video surveillance application that monitors the video feeds
|
|
of an IP camera and records only footage that contains motion. The main
|
|
advantage of this is reduced storage requirements as opposed to continuous
|
|
recording because only video footage of interest is recorded to storage.
|
|
The entire app is designed to operate on just one camera but multiple instances
|
|
of this app can be used to operate multiple cameras.
|
|
|
|
### Usage ###
|
|
|
|
```
|
|
Usage: mow <argument>
|
|
|
|
-h : display usage information about this application.
|
|
-c : path to the config file.
|
|
```
|
|
|
|
### Config File ###
|
|
|
|
The config file is a simple text file that contain parameters that dictate the
|
|
behavior of the application. Below is an example of a config file with all
|
|
parameters supported and descriptions of each parameter.
|
|
```
|
|
# Motion Watch config file v1.2
|
|
#
|
|
# note all lines in this config file that starts with a '#' are ignored.
|
|
# also note to avoid using empty lines. if you're going to need an empty
|
|
# line, start it with a '#'
|
|
#
|
|
recording_stream = rtsp://1.2.3.4:554/h264
|
|
# this is the url to the main stream of the IP camera that will be used
|
|
# to record footage.
|
|
#
|
|
output_dir = /path/to/footage/directory
|
|
# this is the output directory that will be used to store recorded footage
|
|
# from the camera. the file naming convention uses the current date for
|
|
# playlist files which points to hidden video clips taken from the camera.
|
|
#
|
|
buff_dir = /tmp/ramdisk/cam_name
|
|
# this application records small clips of the footage from the camera and
|
|
# then stores them into this directory. any clips with motion detected in
|
|
# them are moved to output_dir, if no motion they are deleted. highly
|
|
# recommend to use a ramdisk tempfs for this since this directory is used
|
|
# for lots of writes.
|
|
#
|
|
color_threshold = 8
|
|
# the color levels in each pixel of the camera stream can range from 0-255.
|
|
# in an ideal world the color differences in between frames should be 0 if
|
|
# there is no motion but must cameras can't do this. the threshold value
|
|
# here is used to filter if the pixels are truly different.
|
|
#
|
|
block_threshold = 3456
|
|
# this application detects motion by loading frames from the camera and
|
|
# then compare the pixels of each back to back frame for any significant
|
|
# differences between the pixels based on color_threshold. it loads the
|
|
# pixels of each frame in blocks. the size of the blocks are adjustable
|
|
# below. it counts how many pixels are different in the block and this is
|
|
# used to tell if the footage has motion if the different pixel count
|
|
# exceeds it.
|
|
#
|
|
block_x = 64
|
|
# this is the x coordinate size or horizontal size of a block of pixels
|
|
# that the application will use to detect the presents of motion.
|
|
#
|
|
block_y = 60
|
|
# this is the y coordinate size or vertical size of a block of pixels
|
|
# that the application will use to detect the presents of motion.
|
|
#
|
|
duration = 60
|
|
# this sets the internal timer used to reset to the detection loop and
|
|
# then call post_cmd if it is defined. note: this time is extended if
|
|
# motion was detected. this will also reload the config file so changes
|
|
# to the settings will be applied without restarting the application.
|
|
#
|
|
post_cmd = move_the_ptz_camera.py
|
|
# this an optional command to run after the internal timer duration has
|
|
# elapsed. one great use for this is to move a ptz camera to the next
|
|
# position of it's patrol pattern. note: the call to this command can be
|
|
# delayed if motion was detected.
|
|
#
|
|
max_days = 15
|
|
# this defines the maximum amount of days worth of video clips that is
|
|
# allowed to be stored in the output_dir. whenever this limit is met,
|
|
# the oldest day is deleted.
|
|
#
|
|
vid_container = mp4
|
|
# this is the video file format to use from recording footage from the
|
|
# camera. the format support depends entirely on the under laying ffmpeg
|
|
# installation.
|
|
```
|
|
|
|
### Setup/Build/Install ###
|
|
|
|
This application is currently only compatible with a Linux based operating
|
|
systems that are capable of building and installing the opencv API from source.
|
|
|
|
The following 3 scripts make this convenient by downloading, compiling and then
|
|
installing the opencv API for you directly from opencv's git repository. This
|
|
also makes sure FFMPEG and all of it's dependencies are installed because this
|
|
application needs it to work properly.
|
|
|
|
note 1: be sure to run setup.sh and install.sh as root (or use sudo).
|
|
note 2: if building from scratch the following scripts will need to
|
|
be run in this order - setup.sh -> build.sh -> install.sh.
|
|
|
|
```
|
|
sh ./setup.sh <--- only need to run this once if compiling for the first
|
|
sh ./build.sh time or if upgrading from the ground up.
|
|
sh ./install.sh
|
|
```
|